Waveguide Elliptical Waveguide   Flexible Waveguide AncillariesSets of Nuts, Bolts, Washers and O-Rings / Gaskets are available to mate appropriate flanges. Each kit contains the correct hardware to mate correctly one pair of flanges. All fixings are corrosion resistant Stainless steel.Double Ridge Flex-Twist Raw Waveguide CoreDouble Ridge Flex-Twist Waveguide CoreDouble ridge waveguide core is manufactured by subjecting conventional rectangular flex twist waveguide core to a secondary pressing operation to create the characteristic ‘figure 8’ cross section. Rectangular Flex-Twist Waveguide CoreFlex / twist waveguide core starts life as spool of 0.1mm thick silver plated brass strip. The strip is then precision rolled into a three dimensional profile before being helically wound around a rotating mandrel to form a continuous rectangular tube with uniform cross section and internal silver plating to minimize loss. Rectangular Seamless Waveguide CoreSeamless flexible waveguide is manufactured from a thin-walled brass tube which is mechanically manipulated into a corrugated form to produce a seamless flexible waveguide. The seamless construction generally allows for greater power & pressure handling although, due to the nature of the construction process, length is limited to 1 meter. Seamless core is offered un-plated as standard with the option of internal silver plating if required. Rectangular Flex-Twist Rectangular Seamless Rigid Waveguide Waveguide Bends Transmission Line Products Cable ConnectorsNew Dehydrator Waveguide

Dehydrator 2589    ADH NETCOM, AC 25527  ADH NETCOM, DC 25896 ADH NETCOM, NEMA  25921  ADH NETCOM,NEMA, MIL-SPEC, TYPE 1 25922  ADH NETCOM,NEMA, MIL-SPEC, TYPE 2 Transmission Line Products Cable ConnectorsNew Dehydrator Waveguide

Connectors Braided Connector Download Data Sheet Elliptical Waveguide Connectors Download Data Sheet Wireless and Radiating Connectors Download Data Sheet   Transmission Line Products Cable Connectors Dehydrator Waveguide

Cable Braided Cable Download Data Sheet Radiating Cables Download Data Sheet Wireless Cables Download Data Sheet   Transmission Line Products Cable ConnectorsNew Dehydrator Waveguide

Redundancy System Receive Redundant Systems Download Data Sheet Transmit Redundant Systems Download Data Sheet   RF Subsystem Beacon Tracking Recievers Block ConvertersNew Block Up Converter Frequency Down Converter Frequency Up ConverterNew Redundancy SwitchesNew Test Loop TranslatorNew Uplink Power Control System Redundancy System

Uplink Power Control System Uplink power controllers, with an embedded beacon receiver module based in Novella’s established compact tracking receiver engine, to adjust transmitted power of an uplink station in accordance with beacon downlink loss at the same location. These are very simple units with up to ten separate IF / gain amplifiers whose gains are adjusted by the DC output voltage provided by the beacon receiver as a measure of beacon level. This is a very simple way of increasing the transmitted power to compensate for uplink fade which is assumed to be approximately the same as the downlink fade.  Maximum depth of fade correction may be selected from 2 to 10dB, and it prevents saturation of the HPA. Download Data Sheet Antenna And Control Systems Beacon Tracking Recievers Block ConvertersNew Block Up Converter Frequency Down Converter Frequency Up ConverterNew Redundancy SwitchesNew Test Loop TranslatorNew Uplink Power Control System Redundancy System

Test Loop Translator The term Test Loop Translator designates a range of frequency converters, usually with the same or similar input and output coverage and bandwidth, with fixed or pre-set Local Oscillator (LO), and preset gain. Some models may be supplied with an agile or pre-settable LO and adjustable gain. They are used to translate signals between uplink and downlink segments of the same band, between uplink or downlink SHF segments and L-band, or between SHF segments of different bands. C to C bandDownload Data SheetC to L bandDownload Data SheetKu to Ku bandDownload Data Sheet RF Subsystem Beacon Tracking Recievers Block ConvertersNew Block Up Converter Frequency Down Converter Frequency Up ConverterNew Redundancy SwitchesNew Test Loop TranslatorNew Uplink Power Control System Redundancy System

Redundancy Switches Novella supplies frequency converter redundant systems in 1:1 up to 1:8 configurations. These systems may be of frequency agile or block converters. The simplest 1:1 redundant system consists of a RU03 unit with two coaxial switches mounted on the rear panel. This system has the advantages of low insertion losses and very good isolation between master and slave signal paths. This system may be used with agile or block converters. Novella supplies also a simple 1:2 system suitable only for block converters. Two sets of three coaxial switches allow a third block converter to function as spare for two master block converters. This configuration is ideal for dual polarisation up or downlinks with L-band interface.   RF Subsystem Beacon Tracking Recievers Block ConvertersNew Block Up Converter Frequency Down Converter Frequency Up ConverterNew Redundancy SwitchesNew Test Loop TranslatorNew Uplink Power Control System Redundancy System

Frequency Up Converter Novella SatComs frequency upconverters are based on a VHF (70 or 140MHz) to L-band module built on a single PCB. The latest frequency synthesis techniques and surface mount components are used to achieve wide coverage, frequency agility, very low phase noise and level of spurii. These modules may be packaged on their own, as L-Band upconverters, or together with L-band to SHF block upconverters (BUCs) as C, X, Ku or DBS-band upconverters. C BandDownload Data SheetDBS BandDownload Data SheetKu BandDownload Data SheetL BandDownload Data SheetS BandDownload Data Sheet RF Subsystem Beacon Tracking Recievers Block ConvertersNew Block Up Converter Frequency Down Converter Frequency Up ConverterNew Redundancy SwitchesNew Test Loop TranslatorNew Uplink Power Control System Redundancy System

Frequency Down Converter Novella SatComs frequency downconverters are based on an L-band to VHF (70 or 140MHz) module built on a single PCB. The latest frequency synthesis techniques and surface mount components are used to achieve wide coverage, frequency agility, very low phase noise and level of spurii. These modules may be packaged on their own, as L-Band downconverters, or together with SHF to L-band Block Downconverters (BDCs) as C, X or Ku-band downconverters. C BandDownload Data SheetKu BandDownload Data SheetL BandDownload Data SheetS BandDownload Data Sheet     RF Subsystem Beacon Tracking Recievers Block Converters Block Up Converter Frequency Down Converter Frequency Up Converter Redundancy Switches Test Loop Translator Uplink Power Control System Redundancy System